CAE LIGHTING / INDUSTRIAL SERIES
SquareBeam
Elite
LIGHT THE TASK.
CONTROL THE SPACE.
60–360 W high bay lighting with three optical distributions and optional Zigbee control.
A shielded lens array, an aluminum body and a choice of controls for warehouses, production halls and indoor high-ceiling spaces.
STANDARD RANGE
160lm/W
Catalog-rated efficacy
POWER OPTIONS
60–360W
Seven standard power ratings
OPTICAL CHOICE
3beams
80° / 110° / 30 × 90°
HOUSING PROTECTION
IP65 / IK10
Catalog ratings; match the model
01 / OPTICAL DESIGN
Put light where
the work happens.
Choose the optic around the rack layout, working plane and mounting height. The shielded lens array is designed to limit direct glare.
80°
Focused distribution
A narrower starting point for higher mounting positions or more concentrated coverage. Check spacing and uniformity in the lighting calculation.
110°
Wide distribution
For broader coverage in open production and circulation areas. Check vertical illumination and glare as well as average floor lux.
30 × 90°
Aisle distribution
An elongated beam for linear layouts and racking aisles. Orient the luminaire to the aisle and verify the beam direction in the IES file.
UGR depends on the selected optic, room geometry, reflectances and observer position. Ask for a project calculation; a universal UGR threshold or maximum mounting height is not specified here.
ZIGBEE CONFIGURATION / SENSOR POSITION
02 / CONTROL OPTIONS
Light responds.
Your space adapts.
Select standard illumination or a matched Zigbee system. The supplied Zigbee documentation covers group control, motion sensing and daylight regulation.
Define each zone
Set the target light level, waiting level, background level and hold times for the way the space is used.
Review the operating data
The documented platform includes energy measurement, failure alerts and sensor-activation heatmaps. Confirm the gateway, software and sensor package in the quotation.
Motion + daylight
Two-step and three-step dimming sequences are documented. Daylight control can maintain a commissioned target illuminance. Final sensor coverage depends on mounting height and site conditions.
Driver compatibility
DALI, 0/1–10 V, PWM and microwave options appear in the family literature. Select one matched driver and control configuration; these functions are not all included as standard.
Standard and Zigbee
The two supplied catalogs use different model codes and output ratings. Compare the separate tables below before choosing a configuration.
03 / MODEL SELECTION
The specification.
In full view.
Standard 160 lm/W series: OSRAM driver / CREE JK 3030 LED configuration, as listed in the supplied V2106 catalog.
| Model | Power | Catalog output | L × W × H (mm) |
|---|---|---|---|
| HB060ME2I-CO | 60 W | 9,600 lm | 362 × 257 × 120 |
| HB100ME2I-CO | 100 W | 16,000 lm | 362 × 257 × 120 |
| HB120ME2I-CO | 120 W | 19,200 lm | 415 × 310 × 120 |
| HB150ME4I-CO | 150 W | 24,000 lm | 487 × 362 × 120 |
| HB200ME4I-CO | 200 W | 32,000 lm | 487 × 362 × 120 |
| HB300ME6I-CO | 300 W | 48,000 lm | 720 × 365 × 130 |
| HB360ME6I-CO | 360 W | 57,600 lm | 720 × 365 × 130 |
Catalog dimensions above follow the standard-series specification table and installation manual. The catalog packing page uses different family codes; confirm the approved drawing and carton data for your order.
| Parameter | Standard 160 lm/W series |
|---|---|
| Input | 220–240 V AC, 50/60 Hz |
| CRI / color consistency | Ra >80 / SDCM <6 |
| Optics | 80°, 110°, 30 × 90° |
| Power factor / THD | >0.95 / <15% |
| Housing | Aluminum |
| Protection | IP65 / IK10 |
| Catalog surge rating | 10 kV for this driver configuration |
| Ambient range | −40 to +50 °C (catalog) |
| Lifetime | 50,000 hours (catalog) |
| Warranty | 5 years (catalog; order terms apply) |
| Mounting | Suspension; bracket option subject to selected kit |
| Light color | Specify required CCT; confirm available configuration |
Match the exact build
The catalog also lists a Philips LED / Sosen driver alternative with a different voltage range and conflicting surge labels. Those values are not merged into the standard table.
Driver, LED, CCT, optic and control choice should appear on the approved specification.
Zigbee series · separate catalog ratings
The Zigbee model table lists 220–240 V AC, Ra >80 and 4000 K. Output is 130 lm/W for 60–300 W and 120 lm/W at 360 W, calculated from the listed power and lumens.
| Zigbee model | Power | Catalog output | L × W × H (mm) |
|---|---|---|---|
| HB060ME2F-CI-Z | 60 W | 7,800 lm | 362 × 257 × 120 |
| HB100ME2F-CI-Z | 100 W | 13,000 lm | 362 × 257 × 120 |
| HB150ME2F-CI-Z | 150 W | 19,500 lm | 415 × 310 × 120 |
| HB200ME4F-CI-Z | 200 W | 26,000 lm | 487 × 362 × 120 |
| HB300ME6F-CI-Z | 300 W | 39,000 lm | 720 × 365 × 130 |
| HB360ME6F-CI-Z | 360 W | 43,200 lm | 720 × 365 × 130 |
The Zigbee 150 W table and dimensional drawing use different model codes and dimensions. Finalize that model against an approved drawing before ordering.
04 / INSTALLATION
Plan the support.
Keep access clear.
Review the ceiling structure, suspension length and maintenance access before installation.
The manual covers suspension and bracket mounting. Select the correct accessory kit and support the luminaire independently of its power cable.
Use the approved model drawing for fixing positions, weight and wiring. Installation and maintenance should be carried out by qualified personnel with the supply isolated.
05 / TEST DOCUMENTATION
See the sample.
Check the evidence.
Inspect the supplied test photographs and match the report, model and configuration to the project specification.
Dust & water
Report LCS210602018BS shows IP6X and IPX5 test photographs for HB300M. This is a photo-documentation excerpt.
Impact test
Report LCS190417040BS identifies HB240M in the supplied sample and impact-test photographs. Request the complete report for scope and results.
Salt-spray exposure
Report LCS210602001CK includes before, during and after photographs. Test duration and acceptance results require the complete report.
THERMAL PERFORMANCE / 360 W SAMPLE
Temperature measured.
Evidence in view.
In-situ measurements for SquareBeam Elite HB360ME6F-CO. See the recorded temperatures, measurement points and original report.
ORIGINAL REPORT GRAPH / UN2005TM002
HB360ME6F-CO
360 W test configuration
Rated 220–240 V AC · 50/60 Hz · 4000 K. Recorded input: 230.1 V, 360.8 W, power factor 0.981.
67.1°C · LED Ts
63.8°C · Driver Tc
25.3°C · Ambient
| Measurement point | Reported temperature | Rise above ambient |
|---|---|---|
| CH 1 · LED Ts | 67.1 °C | 41.8 K |
| CH 2 · PCB Ts | 64.5 °C | 39.2 K |
| CH 3 · Heatsink internal | 62.3 °C | 37.0 K |
| CH 4 · Heatsink external | 61.5 °C | 36.2 K |
| CH 5 · Heatsink external | 44.9 °C | 19.6 K |
| CH 6 · Driver Tc | 63.8 °C | 38.5 K |
| CH 7 · Driver Ta | 57.9 °C | 32.6 K |
| CH 8 · Ambient | 25.3 °C | Reference |
Temperatures reproduced from report UN2005TM002. Temperature rise is calculated against the reported 25.3 °C ambient. These readings describe the tested sample, not every power rating or operating condition.
Document review: the supplied report lists a 2026 test date with calibration due dates in 2020; the graph time axis and stated minimum test duration also differ. Request the corrected revision for formal project approval.
Certificates for your destination
Share the destination country and tender requirements. Ask for model-specific declarations, certificate scans and complete test reports; photographs and catalog logos do not replace those documents.
06 / MANUFACTURING & QUALITY
A closer look
at production.
Explore CAE’s supplied manufacturing and quality-control videos. For your order, agree the inspection plan and request the corresponding records.
01 / Assembly
02 / Aging process
03 / Sample inspection
Agree the inspection record
Confirm the model and driver, optical and electrical checks, control-function testing, finish, labeling and packaging in the order inspection plan. Define sampling and release criteria with CAE.
Support after delivery
The standard catalog states a five-year warranty. Confirm coverage, exclusions, claim evidence and replacement logistics for the supplied configuration. Ask about matched spare drivers, optics and sensors.
07 / PROJECT & ORDER DETAILS
Configure the product.
Agree the delivery.
Send the lighting requirements with the quantity and destination. CAE can review the configuration and quotation scope.
OEM & configuration
Discuss CCT, optics, driver, control package, cable requirements, labels and packaging. Housing or tooling changes require an engineering review and a separately quoted sample schedule.
MOQ & lead time
Standard MOQ, customized MOQ and production lead time are confirmed in the quotation. Include the required delivery date and any sample-approval milestones.
Packing & trade terms
Confirm carton dimensions, net and gross weight and units per carton for the exact model. Request FOB or CIF terms with the named port and destination.
08 / TECHNICAL DOWNLOADS
Build the lighting plan.
Use the original technical files alongside the confirmed configuration. Supplier documents retain the Mildbeam family name and original model references.
Standard catalog
160 lm/W family · V2106 · PDF
Zigbee documentation
Model ratings, control functions and commissioning · PDF
Installation manual
Dimensions, suspension, bracket mounting and care · PDF
PHOTOMETRIC PACK
21 IES files. Three distributions.
60 / 100 / 120 / 150 / 200 / 300 / 360 W, each with D80, D110 and 30 × 90 files. The pack also contains 14 LDT files and 21 photometric PDFs.
IES REFERENCE / HB360ME6F-CO
360 W · thermal-report model
The 360 W IES selection is identified here as HB360ME6F-CO, matching the temperature report model. Select D80, D110 or 30 × 90 for the required distribution.
The downloadable source pack retains its original filenames and test data for traceability. Other wattages keep their own model references; the 360 W thermal results are not assigned to them.
Include the floor plan, mounting height, target lux, rack arrangement and control requirements with your request.
YOUR PROJECT
Transform your next project
with SquareBeam Elite.
Tell us the model or application, quantity and destination. Add mounting height, target lux, optic and control requirements so we can prepare a useful reply.